求教：2011版EN71检测报告中标识怎么处理？

milou

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

EN 71-1:2011版中，CE标识、制造商名称地址等已经不是EN 71-1标准的强制要求，但这些标识仍应符合2009/48/EC。那么，当客户要求出具2011版的EN 71检测报告时，是不是应该加入对2009/48/EC的标识判定才能算是完整报告呢？还是直接无视标识，仅按照EN 71标准判定即可？

大家都是怎么处理的呢？多谢啦~

neve

看客人申请的是什么

13670132272

引用第0楼milou于2011-08-04 14:11发表的 求教：2011版EN71检测报告中标识怎么处理？ :
EN 71-1:2011版中，CE标识、制造商名称地址等已经不是EN 71-1标准的强制要求，但这些标识仍应符合2009/48/EC。那么，当客户要求出具2011版的EN 71检测报告时，是不是应该加入对2009/48/EC的标识判定才能算是完整报告呢？还是直接无视标识，仅按照EN 71标准判定即可？
' z# k/ k) h% c! u+ Z% G
大家都是怎么处理的呢？多谢啦~

回覆
$ Z& n9 w# w! I
7 Warnings, markings and instructions for use (see A.33)
NOTE The text of this note is for information only and the indents do not constitute requirements of this standard. The
/ y$ _+ |* W: Ginformation is not exhaustive and Directive 2009/48/EC and the associated guidance documents should be consulted for
further details.
 Toys made available on the market shall bear the CE marking. The CE marking shall be subject to the general
principles set out in Article 30 of Regulation (EC) No 765/2008. The CE marking shall be affixed visibly, legibly and
indelibly to the toy, to an affixed label or to the packaging. In the case of small toys and toys consisting of small parts,
. i3 @+ g, H6 Z5 wthe CE marking may alternatively be affixed to a label or an accompanying leaflet. Where, in the case of toys sold in
counter displays, that is not technically possible, and on condition that the counter display was originally used as
7 }# C+ Q# @9 ]3 opackaging for the toy, the CE marking may be affixed to the counter display. Where the CE marking is not visible
6 u% j* e* T- E. U6 ]& F  p: @, N" Gfrom outside the packaging, if any, it shall as a minimum be affixed to the packaging. Where specific legislation does
not impose specific dimensions, the CE marking shall be at least 5 mm high.
 The manufacturer’s 1 name, registered trade name or registered trade mark and the address at which the
1 o* R' Q1 q( mmanufacturer can be contacted shall be indicated on the toy or, where that is not possible, on its packaging or in a
3 L: v7 S1 }! I" \document accompanying the toy. This requirement applies also to the name and address etc. of any importer2.
 Manufacturers shall ensure that their toys bear a type, batch, serial or model number or other element allowing their
identification, or where the size or nature of the toy does not allow it, that the required information is provided on the
packaging or in a document accompanying the toy.
 Manufacturers and importers shall ensure that the toy is accompanied by instructions and safety information in a
; P2 |- p$ J5 Ilanguage or languages easily understood by consumers, as determined by the Member State concerned.
# v) ?: G# E2 { A Member State may, within its territory, stipulate that warnings and safety instructions shall be written in a language
or languages easily understood by consumers, as determined by that Member State.

milou

引用第1楼neve于2011-08-04 14:13发表的  :
看客人申请的是什么

只好这样了，现在好多没有标识的产品，只判EN 71合格总觉得不甘心啊，呵呵

neve

引用第3楼milou于2011-08-04 15:38发表的  :
6 ?0 g9 V2 X) F. ?* H, R
' F9 }" R1 O; F/ M+ r5 ]只好这样了，现在好多没有标识的产品，只判EN 71合格总觉得不甘心啊，呵呵

呵呵
& O: e& p0 [/ t* s4 i; A0 V8 }但是你可以给客人建议

helen_zhang

不是强制性要求如果没有这些标识可以不测吧？

muhong

直接做一个*号，然后在最后面把那段内容打进去。

samli

收货

kewee2

引用第0楼milou于2011-08-04 14:11发表的 求教：2011版EN71检测报告中标识怎么处理？ :
EN 71-1:2011版中，CE标识、制造商名称地址等已经不是EN 71-1标准的强制要求，但这些标识仍应符合2009/48/EC。那么，当客户要求出具2011版的EN 71检测报告时，是不是应该加入对2009/48/EC的标识判定才能算是完整报告呢？还是直接无视标识，仅按照EN 71标准判定即可？
' ~8 h* S( R3 h& D. P  J' r
大家都是怎么处理的呢？多谢啦~

想知道，在EN71-1:2011中哪里提到，CE标识、制造商名称地址等已经不是EN 71-1标准的强制要求？

) Z1 _7 \, d) S麻烦楼主指点一下，小弟不太明白。

styu

学习中，