UL153问题

19800108

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

UL153的室外移动灯要做倾倒测试,要求的角度是不是6度呢?如果通过6度后要不要做15度测试,好似还要测试温度的,是不是啊.

ogzl

如果是移动台灯，测试角度为8度,如果是落地灯，比如是可移动的柱灯，其测试角度为12度，户外的不要求做倒地温度测试，室内的才需要过6度倒地温升测试.

chaotao

标准上面没有说落地灯要做12度的哦？请版主明示~~~！！！
UL153只有说：
" z7 y! q2 E' S; F5 D对于装有作为灯的一个部件的玻璃件或灯罩的可移式灯具或装有典型的金属丝网灯罩的可移式灯具，此平面应倾斜至与水增面8度。
; B+ }0 R( S& S0 [) [; m对于具有玩具外形的灯泡，此平面应倾斜至15度，

ogzl

引用第2楼chaotao于2008-05-29 11:45发表的  :
; C2 R$ G2 S" m5 r* H' i/ b标准上面没有说落地灯要做12度的哦？请版主明示~~~！！！
1 T& D% |# e/ g& s8 n# \) O8 h3 ^  _- A$ \UL153只有说：
对于装有作为灯的一个部件的玻璃件或灯罩的可移式灯具或装有典型的金属丝网灯罩的可移式灯具，此平面应倾斜至与水增面8度。
对于具有玩具外形的灯泡，此平面应倾斜至15度，

你说的没错，标准上是没有具体条款，但是这是户外的，要承受户外的风等自然因素，所以一般要求户外的要过12度.（经验之谈)

davey.liao

UL153的132.1.2.3章节有提到如上：

chaotao

引用第3楼ogzl于2008-05-29 14:02发表的  :
) P4 c  R, ~, x8 I! g" G
" ^: w" A5 M4 f. |& E; t你说的没错，标准上是没有具体条款，但是这是户外的，要承受户外的风等自然因素，所以一般要求户外的要过12度.（经验之谈)

: ^7 N; ^& M- c8 f版主分析得有道理，当然测试要求参数一般都会依着标准来，像户外落地灯能通过倾斜8度的测试就可以了。12度是可服合也可不服合是吧？因为我们这里也有一款户外灯具要测试，是否有一种说话，就是说当该灯做稳定测试8度后，是否还要用多大的风吹一下，看是否全倒？以模仿自然环境。

wxjim

我觉得，如果是自己做性能测试，评价一下这个灯好一点还是差一点，可以做12度，甚至做30度，但是如果是做认证，8度足够。

fasten

132 Stability Test
132.1 General
132.1.1 Freestanding units and units intended for both wall and table support shall be tested as described
9 B- E* Z+ n- |3 u9 g+ Vin 132.2 and as modified in 132.3 when provided with a flexible or articulated arm, or as modified in 132.4
when provided with provisions for loading. Compliance criteria is described in 132.5.
7 w1 w+ n" K: J% D, NException: A portable luminaire intended for placement on a shelf and that complies with the Normal
) y. B( G/ {5 E$ N3 XTemperature Test in Sections 124 – 126 in any position and the Drop Test in Section 134 is not required
to comply with this requirement.
132.2 Test method – general
- E: G3 N/ i7 Q9 }( U0 p132.2.1 The portable luminaire, complete with glassware or shade provided as a part of the lamp or with
a representative cloth-and-wire shade when none is provided, is to be placed on the inclined plane and
" U' a1 C! ?( K  Xturned to a position that results in tip over. When the shade is supported by an adjustable harp, or clips
onto the lamp, it is to be positioned so that the lamp-to-shade spacing is equidistant to the lamp.
132.2.2 The plane is to be inclined at an angle of 8 degrees with the horizontal.
/ a" N( i6 y/ y132.2.3 For lamps having toy-like appearance the plane is to be inclined to an angle of 15 degrees.
132.3 Test method – units with flexible or articulated arm
132.3.1 When the portable luminaire has a flexible or articulated arm, the arm is to be bent before the
; v, E* N3 K* Q, olamp is placed on the inclined plane, starting at the lower end of the arm, to form a quarter circle that a
5 F% F& a8 q# D: h5 u8 \% E  Mline joining the ends of the arm make an angle of 45 degrees with the horizontal. When a flexible or
$ B1 n# G3 b- l. T% a# T9 {( Karticulated arm is off-center with respect to the base, the arm is to be bent in the direction that results in
  Y9 z2 `1 z) ltip over. When the unit has more than one flexible or articulated arm, one of the arms is to be adjusted
as for a unit having a single arm, and the other arm or arms are to be extended vertically.
! _4 I+ K0 D* U* ?1 d& P4 xException No. 1: When the unit is not stable on a flat horizontal surface in a particular position, the unit
is not required to be tested in that position.
( H8 F; ^! D( \& b5 Z" u% wException No. 2: Any position of intended use as specified in the manufacturer’s instructions is determined
to be the normal operating position.
4 {5 P8 i+ I' U" |) u: j, a132.4 Test method – units having provisions for loading
132.4.1 A portable luminaire having one or more of the following:
a) Off-center shelf;
* i8 H! `1 _0 u  B+ Nb) Adjustable shelf; or
c) Other provision for loading;
+ V- x" G4 g5 K1 Sshall comply with the stability test in this section when loaded as described in 132.4.2.
8 T$ V+ w& ~7 R- M7 p132.4.2 For the stability test of a portable luminaire as described in 132.4.1, each shelf or other provision
1 i! b& A/ P5 O8 K$ Q& g6 Q; u  yfor loading is to be:
a) Adjusted to the position that results in least stability; and
& S3 S5 u8 l( e- _+ s5 y# i& sb) Loaded with the maximum load specified in the marking required in 169.10; or
c) Loaded with a 15 pound (6.81 kg) weight secured to prevent movement and centered on the
highest shelf or rack.
/ `: M( ~; y9 I132.5 Test results
0 p+ F/ [6 a: R! ]7 x$ o; N132.5.1 The results of the test do not meet the intent of the requirement when the portable luminaire tips
) D: v6 D# U6 R# g% Aover.
3 [/ e0 C0 \# {% S% e
+ x/ y' \4 K6 I) ], a: m4 W18 Portable Luminaires Having Play Value
18.1 A portion of a portable luminaire that has play value for children eight years or less in age and is
intended to be removed from the unit and played with (for example a plush doll not integral with the
& e; B) `$ I8 @" Aluminaire) shall comply with the Federal Regulations for toys and children’s articles. It is not possible to
specify the conditions of tests for all constructions; however, the tests shall include evaluation of impact,
3 d: \/ Q2 u% P4 ibite, flexure, torque, tension, compression, sharp point, sharp edge, and small parts.
18.2 The portable luminaire shall not overturn when tested in accordance with the Stability Test, Section
132, with a 15 degree inclined plane.
18.3 A toy or stuffed animal suspended from a unit shall be designed for unexpected, forceful removal
and shall comply with the requirements in the Test for Suspended Toys, Section 158.
/ |; D9 y% U9 f3 ]) W, J; x( F: [18.4 The portable luminaire shall be marked in accordance with the requirements in 169.11.
Exception: The marking is able to be modified to indicate that the risks are associated with the luminaire
0 \) @* `4 r& V9 Dportion and not to the separable portion having play value.


1 Z9 P1 N9 }- x4 }0 N7 MWORK LIGHTS
116.3 Stability tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
# k0 ^# _- J! {( r1 G3 E# Q0 ~# f116.3 Stability tests
: O3 a& K  Y! F116.3.1 A work light is to be subjected to the Stability Test, Section 132, at an incline of 8 degrees for
! b% O3 y* i, R" s. n% |any possible use adjustment.
116.3.2 A work light complying with Exception No. 2 of 116.2.1 is to be subjected to the Stability Test,
/ R& \+ \  a9 U/ l0 @' {% QSection 132, at an incline of 33 degrees.
116.3.3 The stability test in 116.3.1 and 116.3.2 is to be conducted with any fuel and integral storage
9 k' d3 x" n* C( c; Mcompartments empty.


8 c, h, l* g. E( W: jTUNGSTEN-HALOGEN UNIT
7 ~( J5 ]% N2 z  R- b2 ]147 Tungsten-Halogen Torchiere Stability Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153
3 S; G' u8 z9 p7 I; O) P147.1 General
147.1.1 A floor mounted tungsten-halogen torchiere style portable luminaire not provided with a tipover
% i; {6 Z+ T8 |. M* o) kswitch shall be tested as described in 147.2. Compliance criteria is described in 147.3.
147.2 Test Method
147.2.1 The unit is to be placed on a plane inclined at an angle of 12 degrees with the horizontal and
turned to any position of use presenting the greatest risk of tip over.
. u7 Z/ J4 N0 ]# s5 u147.3 Test Results
147.3.1 The results of the test do not meet the intent of the requirement when the unit tips over.