澳洲插头插座标准AS/NZS 3112中的问题点解释

ljh809809

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

4 _1 l. m2 S) Y1 s* n! t4 s2 {澳洲插头插座标准AS/NZS 3112中的问题点解释

H-RH

直接把问题提出来讨论吧, 你这样问谁敢认自己是高手？

ljh809809

; K; g6 f! R8 V

2.2.3 Form ofpin

Flat pins withthe following width and thickness profiles are deemed to comply:

(a) Flat pinswith a radius on the end with side bevels, as shown in Figure 2.1(h), may havea--

   (i) width profile with an arc on the centreline of the pin of --

     (A) 6mm for all pins of 10A plugs and livepins of 15A plugs; or

     (B) 11mm for earth pins of 15A plugs andall pins of 20A plugs;

问题：6mm和11mm测量的具体部位是什么？

2.2.4 Insulationof plug pins

Plugs up to 15Acomplying with Figure 2.1(a), 2.1(c) or 2.1(f) (flat live pins) and of the insulatedpin plug type do not need to comply with the R20.0±1mm requirements of  Figure 2.1(e).

问题：如何理解？

2.5.1 For rewireableplugs, the anchorage shall be effective for the range of flexible cords listedin Table 2.1, except where--

(a) there is aspecial aperture for the accommodation of only one type or size of flexible cord,a circular hole not being regarded as restricting the entry of cords having diameterssmaller than that of the hole;

问题：如何理解？

In addition,except where the plug is specially designed to accept only parallel two-coreunsheathed flexible cord, the following shall apply to rewireable resilient andthermoplastic plugs of the type referred to in Figure 2.1(a) and Figure 2.1(b):

Two means ofcord grip shall be provided: one that anchors each insulated core by a pillar, post,grip, tortuous path or equally effective means; the second that grips or clampsthe sheathing of the flexible cord. Both means may be incorporated in onedevice.

问题：为什么只是Figure 2.1(a) and Figure 2.1(b)适合这种情况？

2.12.3Additional requirements for rewireable plugs

A rewireableplug shall also be supplied with instructions detailing the following:

(c) Adescription of the method of connection of each conductor giving thepermissible

alternativecolours for the active, neutral and earthing conductors, respectively.

问题：earthing conductors除了用黄绿色，还能有其他的alternative colour?

2.12.6Configuration of plugs

A plugconforming to Figure 2.1(a), Figure 2.1(c), Figure 2.1(f) or Figure 2.1(g)shall have its pins disposed so that, when the pins are correctly connected,the pin configuration, viewed as from the pins, shall be earth, neutral andactive in a clockwise direction.　

问题：Figure (d)不适用这条吗？

2.13.8Temperature rise test

The plug shallbe tested in a draught-free environment at the centre of a plane wooden board,which shall be at least 6 + 2 mm thick, 500 mm wide and 500 mm long withthe rear completely enclosed in a wooden mounting enclosure (wall box) of 90×60×40 mm.

Apertures in thewooden board for the plug pins to pass through are specified in Table 3.1,seeFigure 2.9.

问题：如何在木板上制作出满足插座插销的孔？

2.13.9.1Movement of pins

Plugs shall betested for pin movement by clamping the pin or pins not under test in a rigid　holding block positioned 5 ±0.5 mm from the plug face and applying a forceof 18 ±1 N to the pin under test.The design of the block shall be such that the pin under test shall not comeinto contact with the block during the test.

Except fornon-rewireable plugs, the test shall be carried out without a cord attached tothe plug, and with the terminal screws loosened sufficiently to allow a 1 mm2 conductor to be connected.

The plug andtest equipment shall be preconditioned at a temperature of 40 ±1°C for 1 h,

without the testforce applied. Throughout the test, all parts of the plug and test equipment shallbe maintained at this temperature.

For all plugs,the point of application of the force shall be 14 ±0.5 mm from the face of the plug along the pins, and thedirection of the force shall be--

(a) in bothdirections along the line perpendicular to the plane of the pin, and passing throughthe centre of the pin; and

(b) in thatplane in both directions along a line at right angles to that specified in Item(a).

Over a period of10 s, the force shall be gradually applied to each of the pins in the manner　prescribed in Items (a) and (b), maintained atits maximum value for 10 s, and then released. The deflection of the pins shallbe measured along the line of force relative to the face of the rigid holdingblock during the period when the force is applied. The maximum deflection shallnot exceed 2.0 mm.

问题：此条款的检测设备是什么样的？如何做检测？

ljh809809

SOCKET-OUTLETS

3.6.1 Pin entryapertures for plugs

NOTE: Anycontouring or shaping of a faceplate or socket-outlet face within 13.7 mm from anyedge of a live pin aperture, needs to be below the plane of the surfacesurrounding the pin apertures, but cannot be more than 3 mm below that plane.

问题：此处的最大3mm与Figure 3.3矛盾？

3.6.3Socket-outlet faceplate

No part of thedevice, including any switch in any position, shall project more than 8.6 mm fromthe surface of the socket-outlet face within the shaded area of Figure 3.4.This requirement applies to all socket-outlets except those with special designfeatures, such as providing protection from dust, weather or mechanical damage.

In case ofdoubt, to verify projections on the socket face do not interfere when a plug orplug in device is inserted, insert the gauge of Appendix D modified as follows,the dimension of the diameter 38 is changed to 43.2, this diameter becomes araised boss of 8.6 mm to stimulate a plug/plug in device. When inserted themodified gauge shall not interfere with any part of the device or switch.

问题：满足图3.4阴影部分的各边长为60mm,为何用直径为43.2mm的量规可以确定开关附件是不是满足标准？

3.11.1Socket-outlets switched by insertion of plug pins

In addition tocomplying with this Standard, the switching function of socket-outlets switchedby insertion of plug pins and intended for use with a plug complying with Figure2.1(a), Figure 2.1(c) or Figure 2.1(d) shall comply with the requirements of Clause3.11.2 except that the ‘ON’ position need not be indicated.

问题：除了Figure 2.1(a), Figure 2.1(c) or Figure 2.1(d)之外，其他图中的开关不适用吗？

3.11.2Socket-outlet switches

Any switchintended for the control of a low voltage socket-outlet to be used with a plug complyingwith Figure 2.1(a), Figure 2.1(c) or Figure 2.1(d) shall comply with therelevant requirements of AS/NZS 3133. All switches provided shall be Category 2switches and their ‘ON’ position shall be indicated in accordance with therequirements of AS/NZS 3100 for the visual indication of the positions ofswitches.

问题：除了Figure 2.1(a), Figure 2.1(c) or Figure 2.1(d)之外，其他图中的开关不适用吗？

3.12 SHUTTEREDSOCKET-OUTLETS

If asocket-outlet contains shutters, the shutters shall be activated by the neutralpin of a plug complying with Figure 2.1(c) to allow full insertion of this typeof plug without undue force. Compliance is checked by inspection and manualtest, if necessary.

问题：只有Figure 2.1(c)适用吗？只有用neutral pin来检验遮蔽门吗？

3.14 TESTS FORSOCKET-OUTLETS

3.14.1 General

Socket-outletsshall be mounted as in normal service and as follows:

(a) Flush andsemi-flush socket-outlets that may be used in walls with thermal insulation shallbe mounted on a vertical wooden surface, not more than 6 mm thick, with the portiondesigned to fit into the recess completely enclosed in absorbent cotton wool, looselypacked and held in position by an appropriate metallic (wall box) enclosure.

(b) Othersocket-outlets shall be mounted in the minimum size enclosure or wall box.

问题：此处的enclosure or wall box是金属的还是木质的？

NOTE: Anappropriate metallic enclosure for socket-outlets on mounting plates of approximatelyH 114 mm × W 72 mm with 84 mm centres isone of H 90 mm×W 60mm×D 40 mm (approximatingdimensions of commonly available units).

问题：如何理解这段话？

3.14.2Insulation resistance test No. 1

For the purposeof this test the socket-outlet shall be mounted to a metal plate and in appropriatemetallic enclosure, using the fixing holes provided, by means of metal fixing screwscorresponding in respect of their diameter and size and type of head, with thescrews that would normally be used for fixing the socket-outlet.

NOTES:

1 The metalplate is to be approximately 1 mm thick and be larger than the projected areaof the

socket and havea cut-out as recommended by the manufacturer.

2 An appropriatemetallic enclosure is described in Clause 3.14.1.

问题：此处的metal plate and metallic enclosure指的是与上面3.14.1（b）中一样的metal plate and metallic enclosure？

3.14.5 Test oftemperature rise

For multi-outletsocket-outlet units, the test shall be conducted on one outlet of each type,the outlet(s) not under test being maintained in a no-load condition.

问题：如果同一个插座板上有不同类型的插座，温升试验是同时做的吗？

3.14.8.2Withdrawal force test

Plugs rated at10 A and complying with Figure 2.1(a1) of this Standard and which have not beensubjected to any previous tests shall be used. A separate plug shall be usedfor testing each socket-outlet.

问题：此处的插拔力试验用插头每次都要用新的吗？

ljh809809

图3.3和表2.4没办法贴上去。

ljh809809

期待懂澳洲插头的同行解惑。谢谢！

ljh809809

没有人指导一下。

ljh809809

7 d9 |  ], A0 c, V1 ^
:(:(:(:(

ljh809809

今天亲自登门请教了一下高手。我自己来解答。

ljh809809

2.2.3 Form ofpin
Flat pins withthe following width and thickness profiles are deemed to comply:
$ ]# l9 d! Q$ Z) I5 v+ f(a) Flat pinswith a radius on the end with side bevels, as shown in Figure 2.1(h), may havea--
5 W) y( p0 `: }, ^3 i   (i) width profile with an arc on the centreline of the pin of --
  t$ h# O+ `, o     (A) 6mm for all pins of 10A plugs and livepins of 15A plugs; or
     (B) 11mm for earth pins of 15A plugs andall pins of 20A plugs;
问题：6mm和11mm测量的具体部位是什么？

答：6mm和11mm是指弧度所对应的半径。