请教大神怎么看UL294第32章节的爬电距离和电气间隙

jansle_happy

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

# p+ a6 u- Z, m, B* O1 ~, y( x
如题，请教大神怎么看UL294第32章节的爬电距离和电气间隙，他要求是非绝缘带电部件和相关非绝缘带电部件以及dead-metal部件之间爬电距离和电气间隙需要满足下表要求，但是看起来是所有非绝缘部件都需要看，不管电压是危险电压还是非危险电压，这个看起来不符合逻辑啊，一般safety的标准不是只会看危险电压么？另外，表格中有些电压段是有重复，比如other栏中有两个31-150V，但是给定的爬电距离和电气间隙又不同，到底要怎么看？
6 f/ |, @; {0 Q" ]( sSPACINGS
0 S3 U- _) a4 P0 ~9 M# Z: M32 General
32.1 Except as specified in 33.2, spacings between uninsulated live parts or between uninsulated live parts and dead-metal parts shall not be less than those indicated in 32.2 – 32.5.
0 v) A/ a. v; J# \! k0 `/ s( J32.2 Where deformation of the enclosure is likely to reduce spacings, the spacings between an uninsulated live part and:
# |( D8 F: K6 l' N  y% i     a) A wall or cover of a metal enclosure;
! X& x$ Q+ l0 J0 c$ _/ O8 k     b) A fitting for conduit or metal-clad cable; and
     c) A metal piece attached to a metal enclosure, where deformation of the enclosure is likely to reduce spacings,
6 Y6 Q0 \% w3 ~shall not be less than those indicated in Table 32.1. Also see Figure 32.1.

8 S" K& X0 Z1 A/ E& ]+ ~1 G. j
# b' v) N4 @# T32.3 The spacings between an uninsulated live part and:
% a& m; R; t* L& j& K    a) An uninsulated live part of opposite polarity,
( z$ q" o4 j' I. Z$ q    b) An uninsulated grounded dead-metal part other than the enclosure, and
) [% Y& F8 M' l    c) An exposed dead-metal part that is isolated (insulated),
shall not be less than those indicated in Table 32.1. See 33.1 – 33.4 for exceptions to this requirement.

32.4 If a short circuit between uninsulated live parts of the same polarity would prevent the intended operation of the product, the spacings between the uninsulated live parts shall not be less than those indicated for ″Other parts″ in Table 32.1.

32.5 Film-coated wire is considered an uninsulated live part in determining compliance of a product with the spacing requirements, but film coating may be used as turn-to-turn insulation in coils.


! q* J5 p$ t+ f# U! r' X

Hellsinger12

我是这样觉得的
0 R7 G; q+ E' W9 j6 J9 [% |% i3 Q1.因为table 32.1包含了三个位置的安全距离 a) 正负极之间功能绝缘 b) 带电体于接地金属 c) 带电体与塑料表面，针对0-30VAC的安全电压只要考虑a）正负极之间功能绝缘即可
! n2 N: ]  s* k4 ~) i) R9 {' ~) O! w2.Other parts对应的距离要求是最后三行，上两行的距离要求是上一页的 Non Class 2, power-limited

jansle_happy

Hellsinger12 发表于 2022-5-30 13:28
我是这样觉得的
1.因为table 32.1包含了三个位置的安全距离 a) 正负极之间功能绝缘 b) 带电体于接地金属 c ...

感谢大神分享。