EN61558和EN61347有什么差别呢？

小猫咪 · 发表于 2012-9-12 14:01

有哪位大侠知道这两个标准有什么差别的？请指点下。

qsin · 发表于 2012-9-12 14:25

1) 标准名称
61347-1
Lamp controlgear –
Part 1:
General and safety requirements

61558-1
Safety of power transformers, power supplies, reactors and similar products –
Part 1: General requirements and tests

2) 范围
61347-1
This part of IEC 61347 specifies general and safety requirements for lamp controlgear for use
on d.c. supplies up to 250 V and/or a.c. supplies up to 1 000 V at 50 Hz or 60 Hz.
This standard also covers lamp controlgear for lamps which are not yet standardized.
Tests dealt with in this standard are type tests. Requirements for testing individual lamp
controlgear during production are not included.
Requirements for semi-luminaires are given in IEC 60598-1 (see definition 1.2.60).
In addition to the requirements given in this Part 1 of IEC 61347, Annex B sets out general
and safety requirements applicable to thermally protected lamp controlgear.
Annex C sets out additional general and safety requirements as they apply to electronic lamp
controlgear with means of protection against overheating.
Additional requirements for built-in ballasts with double or reinforced insulation are given in
Annex I.

61558
This International Standard deals with safety aspects of power transformers, power supplies,
reactors and similar products such as electrical, thermal and mechanical safety.
This standard covers the following types of dry-type transformers, power supplies, including
switch mode power supplies, and reactors, the windings of which may be encapsulated or
non-encapsulated :
NOTE 1 The distinction between transformers, power supplies and switch mode power supplies is as follows:
– for transformers, there is no change in frequency .However, transformers (e.g. constant voltage
transformers) may have an internal resonance frequency not exceeding 30 kHz;
– for power supplies, the internal operational frequency and waveform are different from the supply frequency
and waveform, and the internal operational frequency does not exceed 500 Hz (see definition 3.1.19);
– for switch mode power supplies, the internal operational frequency and waveform are different from the
supply frequency and waveform and the internal operational frequency exceeds 500 Hz and does not exceed
100 MHz.
The relevant parts 2 may be found in the introduction of this standard.
a) Stationary or portable, single-phase or poly-phase, air-cooled (natural or forced), isolating
and safety isolating transformers, independent or associated, not forming a part of
distribution networks and with the following characteristics:
– rated supply voltage not exceeding 1 000 V a.c.;
– rated supply frequency not exceeding 500 Hz;
and complying with the following values, unless otherwise specified in the relevant part 2:
• for isolating transformers:
– rated output for single phase transformers, not exceeding 25 kVA, and for polyphase
transformers not exceeding 40 kVA.
– no-load output voltage and the rated output voltage exceeding 50 V a.c., and not
exceeding 500 V a.c, or 1 000 V a.c. to be in accordance with the National Wiring
Rules or for a special application.
• for safety isolating transformers:
– rated output for single phase transformers not exceeding 10 kVA, and for polyphase
transformers not exceeding 16 kVA.
– no-load output voltage and the rated output voltage not exceeding 50 V a.c.
between conductors, or between any conductor and protective earth.
NOTE 1 Isolating and safety isolating transformers are used where double or reinforced insulation between
circuits is required by the installation rules or by the appliance specification (for example toys, bells, portable tools,handlamps).
b) Stationary or portable, single-phase or polyphase, air-cooled (natural or forced)
separating transformers, auto-transformers, variable transformers and small reactors,
independent or associated, not forming a part of distribution networks and with the
following characteristics:
– rated supply voltage not exceeding 1 000 V a.c.;
– rated supply frequency not exceeding 500 Hz;
and complying with the following values, unless otherwise specified in the relevant part 2:
– no-load output voltage or a rated output voltage for both independent and associated
transformers not exceeding 15 kV a.c., and for independent transformers, a rated
output voltage not less than 50 V a.c.;
– rated output not exceeding the following values:
– 1 kVA for single-phase transformers;
– 2 kVAR for single-phase reactors;
– 5 kVA for poly-phase transformers;
– 10 kVAR for poly-phase reactors.
NOTE 2 Separating transformers are used where double or reinforced insulation between circuits is not
required by the installation rules or by the appliance specification.
NOTE 3 Normally, the transformers of type b) are intended to be associated with the equipment to provide
voltages different from the supply voltage for the functional requirements of the equipment. The protection against
electric shock may be provided or completed by other features of the equipment, such as the body. Parts of output
circuits may be connected to the input circuit or to the protective earth.
c) Stationary or portable, single-phase or polyphase, air-cooled (natural or forced),
independent or associated power supplies and switch mode power supplies
incorporating one or more transformer(s) of type a) or b), not forming a part of distribution
networks and with the following characteristics:
– rated supply voltage not exceeding 1 000 V a.c.;
– rated supply frequency not exceeding 500 Hz;
– internal operational frequency for power supplies not exceeding 500 Hz and for switch
mode power supplies not exceeding 100 MHz;
and with the following values, unless otherwise specified in the relevant part 2:
• for power supplies and switch mode power supplies incorporating isolating
transformers:
– rated output for single- phase or polyphase power supplies or switch mode
power supplies not exceeding 1 kVA;
– no-load output voltage and the rated output voltage exceeding 50 V a.c. or
120 V ripple- free d.c., and not exceeding 500 V a.c. or 708 V ripple- free d.c., or
1 000 V a.c. or 1 415 V ripple- free d.c. to be in accordance with national wiring rules or
for a special application;
• for power supplies and switch mode power supplies incorporating safety isolating
transformers:
– rated output for single- phase or polyphase power supplies and switch mode
power supplies not exceeding 1 kVA;
– no-load output voltage and rated output voltage not exceeding 50 V a.c.or 120 V
ripple- free d.c. between conductors, or between any conductor and protective earth.
NOTE 4 Power supplies and switch mode power supplies incorporating Isolating and safety
isolating transformers are used where double or reinforced insulation between circuits is required by
the installation rules or by the appliance specification (for example toys, bells, portable tools, handlamps).
• for power supplies and switch mode power supplies incorporating separating
transformers, auto-transformers , and variable transformers:
– rated output for single-phase or polyphase power supplies and switch mode
power supplies not exceeding 1 kVA;
– no-load output voltage and rated output voltage for both, independent and
associated transformers not exceeding 15 kV a.c., and for independent
transformers, a rated output voltage not less than 50 V a.c.;
NOTE 5 Power supplies and switch mode power supplies incorporating separating transformers are
used where double or reinforced insulation between circuits is not required by the installation rules or by
the appliance specification.
d) This standard is also applicable to tw-marked transformers with a rated output not
exceeding 1 000 VA and where the tw-temperature does not exceed 140 °C (tw 140).
However, tw -marking of transformers is optional.
This standard also applies to transformers, power supplies, switch mode power supplies,
and reactors incorporating electronic circuits.
This standard does not apply to external circuits and their components intended to be
connected to the input and output terminals or socket-outlets of the transformers, power
supplies and switch mode power supplies, and reactors.
NOTE 6 Attention is drawn to the following:
– for transformers intended to be used in vehicles, on board ships, and aircraft, additional requirements (from
other applicable standards, National Rules, etc...) may be necessary;
– measures to protect the enclosure and the components inside the enclosure against external influences like
fungus, vermin , termites, solar-radiation, and icing should also be considered;
– the different conditions for transportation, storage, and operation of the transformers should also be
considered;
– additional requirements in accordance with other appropriate standards and national rules may be applicable to
transformers intended for use in special environments, such as tropical environment
NOTE 7 Future technological development of transformers may necessitate a need to increase the upper limit of
the frequencies; until then this standard may be used as a guidance document.

EN的标准和IEC的有点小差异，但范围是一致的

stey · 发表于 2012-9-12 14:40

分别是变压器与镇流器的标准

小猫咪 · 发表于 2012-9-12 15:01

qsin 发表于 2012-9-12 14:25
: _& T6 Q+ n" N* A0 y( z" v1) 标准名称1 a7 y' R6 H2 {' ^9 i$ M
61347-18 ?5 \* ]/ K) e5 T
Lamp controlgear –

多谢。

		自动登录	找回密码
密码			注册安规

	安规论坛 \| 仪器设备 \| 求职招聘 \| 国家标准		公告 \| 教程 \| 家电 \| 灯具 \| 环保 \| ITAV		签到充值在线打卡设备		好友\| 帖子\| 空间\| 日志\| 相册
	IP淋雨机 \| 证书查询 \| 规范下载 \| 资质查询		招聘 \| 考试 \| 线缆 \| 玩具 \| 标准 \| 综合		红包邮箱打卡工资禁言		分享\| 记录\| 道具\| 勋章\| 任务

IP淋雨设备\| 恒温恒湿箱\| 拉力机\| 医疗检测设备	沙特Saber 埃及COI 中东GCC｜CoC直接发证机构	水平垂直燃烧机\|灼热丝\|针焰试验机\|漏电起痕试验机
灯头量规\|试验指\|插头插座量规\|灯具检测设备	耐划痕试验机\|可程式恒温恒湿试验箱 \| 耦合器设备	广东安规-原厂生产-满足标准-审核无忧

[IEC灯具] EN61558和EN61347有什么差别呢？

浏览过的版块

安规网为您推荐 /2