逆变器软件评估

海之未央

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

貌似从最近开始，所有非隔离逆变器的认证都会需要评估软件了，，，，欧洲是60730标准，北美是Ul1998标准，。，，，，有哪位大虾做过这一块的可以分享一下经验呢~

戏尘

评估的系统很多 比如软件的控制功能 各种命令 等 要资料给我站内信

ok_hmh

其实一直都有要软件评估，但是机构都没做这个。希望这次能实现。

戏尘

可以出一份报告的呀 不知楼主是否看过此类报告

戏尘

        Voltage monitoring

* b8 n1 t1 w2 c  c* e
9 J! s( x* o5 a8 \1 [- U# b5 y        Frequency monitoring
/ n+ x$ |* K4 ~  D* j+ F2 i- m& L

; }9 O) i0 h" `6 X  m        RCD (RCMU) monitoring


, Z/ @" v* E7 Y+ w" F. n        Islanding detection

$ m- B: W8 }6 Z0 L$ Y% ^
! n0 E7 e7 w4 \( v, w
3 T; p: h! c7 K! n' Q; U" O        Insulation detection

) @- r2 W& Y! e
: V0 f) H' P0 c        I/P, O/P voltage/current detection

: Q4 j- O+ F  A
        O/P power control
1 M, O0 I! j( x( \- m& Q8 g   

2 f. n4 F* l8 s1 T( q2 V1 W+ J8 w- D        Self test
6 {  p  s# M$ W- d" u  }& P( j8 _

戏尘

软件描述 硬件描述都需要写在报告中的

戏尘

Hardware Description
" P9 @. {; \+ `( U. e2 v( d        DC/AC Inverter
) v& W/ ~5 _- _8 {The Inverter will convert from the direct current (DC) to the alternating current (AC); the converted AC could generate any voltage and frequency by requirement with transformer, switching and control circuits. After converter, the inverter will generate a nearly perfect sine wave output (<3% total harmonic distortion) that is essentially the same as utility-supplied grid power. Thus it is compatible with all AC electronic devices. This is the on-grid type inverters. The design is more complex, and costs more per unit power. The electrical inverter is a high-power electronic oscillator. It is so named because early mechanical AC to DC converters was made to work in reverse, and thus were "inverted", to convert DC to AC.

7 U! r3 h$ T; l6 c- v0 v* J4 C2 x! ]! y: {        DSP Controller & MCU Controller
The internal control is redundant built. It consists out of two controllers (U7, U9), the master DSP controller (U7) can control the relays, measures voltage, frequency, AC current with injected DC, insulation resistance and residual current. In addition it tests the current sensors before each start up.  The slave MCU (U9) can also shut down the relays.  Both microcontrollers communicate with each other.
* ?7 L8 \3 s4 X; _6 a9 G
9 q: V6 ~( R; ~" i- B/ b9 ]* K        RCMU Circuit
- B5 V$ u0 l: @$ n5 z& HThe RCMU (Residual Current Measurement Unit) monitors the AC residual currents between the inverter and the output filter. The residual current also will be checked and monitored by the two controllers (Master DSP/Slave MCU) separately.
; u: g% w* s- Z! c9 _
        Grid disconnection
% h- c0 i  y3 R& h0 I( `% v  zThe units provide two relays in series in each phase. The relays are tested self before each start-up.
: Z1 v  ]" V- @

戏尘

还要很多这只是其中一部分

yeanling

做评估的话，软件代码是不是也要提供？

海之未央

戏尘 发表于 2012-8-23 23:28
$ A) Q' i: b6 A  S8 F# E        Voltage monitoring

; m, H& K& s6 H5 {  J1 @对，好像就是这些功能，印象中跟UL那个鬼佬问过，如果我们做了软件评估之后就可以不做双CPU了。