安规网

标题: 请教各位高手,接线端子,尼龙扎带,电镀,有色金属需要通过什么认证?能否提供标准 [打印本页]

作者: zhoupiyan    时间: 2007-7-23 14:03
标题: 请教各位高手,接线端子,尼龙扎带,电镀,有色金属需要通过什么认证?能否提供标准
请教各位高手,接线端子,尼龙扎带,电镀,有色金属需要通过什么认证?能否提供标准?我是新手不懂啊,多谢各位高手回答!
作者: pwong03492    时间: 2007-7-23 16:05
引用第0楼zhoupiyan于2007-07-23 14:03发表的 请教各位高手,接线端子,尼龙扎带,电镀,有色金属需要通过什么认证?能否提供标准? :0 c1 F( c# C# R; G; E8 t
请教各位高手,接线端子,尼龙扎带,电镀,有色金属需要通过什么认证?能否提供标准?我是新手不懂啊,多谢各位高手回答!

* T2 M: {$ T2 B! Y# W- P在申请UL的应用中, 接线端子, 尼龙扎带是需要UL认证的
; s2 a8 j& N4 q$ Z: e, C- 接线端子, 不知道你说的是哪一种. 有 Quick-connect terminals (UL310, CCN: RFWV)
4 q' w9 V* \% Z9 k, i5 ]- 尼龙扎带, 塑胶有UL即可 (CCN: QMFZ2).
  X" m: Y& N7 j  V6 M7 |7 K+ q+ i! I& U5 `
其他, 我也不清楚, 期待朋友们分享经验.
作者: nellhu    时间: 2007-7-23 16:07
接线端子, 尼龙扎带如果是IEC好象没有要求认证的。
作者: zhoupiyan    时间: 2007-7-24 09:04
非常感谢pwong03492 ,nellhu两个高手的答疑,多谢!接线端子是公控低压电器用的
作者: lcky    时间: 2007-7-25 00:50
出美国和加拿大的话, 尼龙扎带要UL或CSA认证; K$ K- m& W0 V( N+ }+ v; G
UL1565 Positioning Devices$ L5 _9 Z+ @# O* }! m* C* B8 z& T
This is the common CSA and UL Standard for positioning devices. It is the first edition of CSA C22.2 No.0 y( e  z( H, `7 d$ u) _4 M9 J
18.5, and the fourth edition of UL 1565.  j5 ]" L8 q/ ~0 q
1 Scope0 o$ P& F: n. X4 N  N
1.1 This standard applies to those metallic and nonmetallic devices used for positioning – which may
9 e7 Z, B1 h" Q1 C5 r2 finclude bundling and securing – or to a limited extent supporting cable, wire, conduit, or tubing of a wiring
* i3 |0 D6 V0 R9 S$ O4 \  q% v5 M3 s- Zsystem in electrical installations, to reduce the risk of fire, electric shock, or injury to persons. This
/ m2 C5 C$ Y3 a" a- y: R8 Cstandard applies to, but is not limited to, cable ties, cable tie mounting blocks, cable clamps, cable and" ~  a/ e6 _6 ~6 `
conduit clips, and non-raceway ducts.. M5 Q( ^, g4 B; T( c9 D
1.2 These requirements do not apply to coated electrical sleeving, extruded insulating tubing, metallic or% M2 S+ `$ g" }4 I3 D  A5 j
nonmetallic raceways or woven flexible nonmetallic tubing (fiber loom), employed as mechanical
0 _  K3 N0 T$ K9 C9 g9 _protection for insulated wires or equipment covered by other standards or requirements.
) A* s) q2 l/ `6 d8 J+ [  G- t1.3 These requirements do not apply to any mechanical protection or electrical insulation that is provided
8 W3 x1 Y7 u! s; [/ U2 H2 R" xby these devices.% }, I  c. d4 i' k6 J) [0 w7 ]
1.4 In Canada, the requirements in this standard generally address class of workmanship in accordance
' T, N8 R, {( T* X2 E  cwith the Canadian Electrical Code Part 1, and where applicable, minor combustible components in the
7 P; s* I6 X# n6 @4 t- pNational Building Code of Canada.




欢迎光临 安规网 (http://bbs2.angui.org/) Powered by Discuz! X3.2